Amana AM26LP-P Use and Care Guide

AMANA®THREE BURNER GAS GRILLAssembly/Installation Instructions and Use & Care GuideFor questions about features, operation/performance, parts, acc

BStep 3: Assemble Rear Top Cross BarASSEMBLY INSTRUCTIONSA101. Use four (4) Self tapping screws to secure the rear top cross bar in position as shown.

111. Use four (4) M6 x 16 phillips pan head screws to secure the Grill cart base to the support polesas shown.Note: Add flat washer and lock washer th

121. Install the casters to the support poles with the Hex nut wrench provided.Note: The casters with locks should be on the right side of the grill.A

1. Have someone help you to stand the grill upright.2. Use three (3) self-tapping screws to secure the heat shield in position.A. Heat shieldB. Self-t

ASSEMBLY INSTRUCTIONSStep 7: Assemble Front Panel1. Use six (6) self-tapping screws to secure the front panel in postion as shown. The decorativeslots

ASSEMBLY INSTRUCTIONSStep 8: Assemble Side Shelf Left1. Loosen the four (4) 5/16-24 Hex Head screws on the left side of the grill as shown.2. Attach t

1. Remove the brass burner cap attached with tape along with side burner grate and set aside.2. Loosen the four (4) 5/16-24 hex head screws.3. Attach

ASSEMBLY INSTRUCTIONSStep 10: Assemble the Side Valve1. Using a Phillips screwdriver, remove the 2 screws from the side burner valve assembly.2. Push

ASSEMBLY INSTRUCTIONSStep 11: Assemble the Side Burner Casting1. Remove the two phillips pan head screws from the side burner casting.2. Angle the sid

ASSEMBLY INSTRUCTIONSStep 12: Assemble the Side Valve1. Use the two (2) screws removed in step 1 on page 18 to secure the head of side burner castingo

TABLE OF CONTENTS2OUTDOOR GRILL SAFETY...3-4U

ASSEMBLY INSTRUCTIONSStep 13: Assemble Igniter ModuleEAA. Igniter moduleB. Side burner igniter wireC. Main burner igniter wiresD. Igniter push buttonE

ASSEMBLY INSTRUCTIONSStep 14: Assemble the Side Burner Accessories1. Center the brass burner cap on top of the side burner head.2. Place the side burn

ASSEMBLY INSTRUCTIONSStep 15: Assemble the Drip Pan1. Place the drip pan onto the drip pan holder underneath the grill head assembly.ABA. Drip panB. D

23ABCA. Flavor gridsB. Main cooking gratesC. Bread warming rack1. Insert the flavor grids into the cutouts with triangle ridges facing up.2. Install m

24”24”24INSTALLATION REQUIREMENTSSelect a location that provides minimum exposure to wind and traffic paths. The locationshould be away from strong dr

Product Dimensions54.5”(138.5cm)45”(114.3cm)33.9”(86cm)26”(66cm)13.3”(33.7cm)20.6”(52.4cm)22.4”(56.9cm)Observe all governing codes and ordinances.IMPO

Gas Supply Line Pressure TestingTesting above ½ psi (3.5 kPa) or 14" (35.5 cm) WCP (gauge):The grill and its individual shutoff valve must be dis

Check the burnersThe burners are tested and factory-set for most efficient operation. However, variations in gas supplyand other conditions may make m

28OUTDOOR GRILL USEUsing Your Outdoor GrillInspect the LP Gas Fuel Cylinder Supply HoseInspect the gas pressure regulator/hose assembly before each us

Using Your Outdoor Grill (cont.)Manually Lighting Grill1. Do not lean over the grill.2. Remove the manual lighting extension and attach a match to the

OUTDOOR GRILL SAFETYYour safety and the safety of others are very important.We have provided many important safety messages in this manual and on your

TIPS FOR OUTDOOR GRILLING30Before Grilling Thaw food items before grilling. Lightly oil the grill grates or the food when cooking low-fat cuts of me

OUTDOOR GRILL CAREReplacing the Igniter BatteryIf igniters stop sparking, the battery should be replaced.1. Unscrew igniter button cap counter clockwi

32OUTDOOR GRILL CARE (cont.)General Cleaning (cont.)WARMING SHELFCleaning Method: Liquid detergent or an all-purpose cleaner. Rinse with clean water

33OUTDOOR GRILL CARE (cont.)General Cleaning (cont.)DRIP PAN AND SHELFIMPORTANT: The drip pan should only be removed when grill is completely cool.The

TROUBLE SHOOTINGGrill will not light Is the 20 lb LP gas fuel cylinder valve turned off?Turn the 20 lb LP gas fuel cylinder on. Is the grill properl

35REPLACEMENT PARTSHood Assembly Front Face OverlayFCTG2608001 FCTG26080071 set 1 setHood Handle Amana LogoFCTG2608002 FCTG26080081 pcs 1 pcsTemp Guag

36REPLACEMENT PARTSGrill Support Pole FL/BR Grill Support Pole FR/BLFCTG2608014 FCTG26080212 pcs 2 pcsRear Top Cross Bar Swivel Caster with LockFCTG26

37REPLACEMENT PARTSSide Burner Right Assy.side burner igniter with wire300FCTG2608028 FCTG26080301 set 1 pcsIgniter Module 4 poles Side Burner ValveFC

AMANA® is a registered trademark of Maytag Corporation or its related companies and is used under license toSure Heat Manufacturing© 2008.All rights r

IMPORTANT SAFETY INSTRUCTIONSIMPORTANT: This grill is manufactured for outdoor use only. For grills that are to be used atelevations above 2000 ft (60

1. Using a utility knife, cut the tape to open top flaps ofcarton.2. Remove Assembly/Installation Instructions and Use andCare Guide.3. Remove the lar

Assembly Hardware Supplied 21 - self-tapping screws 8 - M6 x 65 Phillips pan head screws 4 - M6 x 16 Phillips pan head screws 1 - Side burner knob

ASSEMBLED GRILL VIEW7ABCFDEGHIJA. Control knob: main burnersB. Side shelfC. Grilling/cooking surfaceD. Roll top grill hoodE. Hood handleF. Bread warmi

ASSEMBLY INSTRUCTIONSStep 1: Assemble Grill Cart Base1. Insert the end of cylinder retention bar through the holes of the cart base as shown.2. Use fo

Step 2: Assemble Support PolesABCASSEMBLY INSTRUCTIONS91. Tilt the grill head assembly onto back with control panel facing up.2. Use eight (8) M6 x 65