Amana RADARANGE RW321T User Manual download pdf (Page 6)

CHECKING OVEN OPERATION ■

A. Set the optional entry signal. This optional signai can be

set to “beep” whenever a pad is pressed. It confirms the

oven has “read” and accepted your entry.

To program the entry signal:

1. Plug in the oven. Dash lines wiil appear in the dispiay.

2. Press 0. The oven wiil “beep” now and whenever you

press any pad.

To cancel the entry signal:

Unplug the oven and reconnect it, but do not press 0. Dash

iines wiil appear in the dispiay. The oven wiii not beep when

you press the pads.

B. To deactivate the end-of-cycle signal.

This optional signal can be set to “beep” to indicate when

cooking time has eiapsed and when food has reached a set

temperature. The signal is automatically set when you plug in

the oven.

To cancel the end-of-cycle signal:

Press TIMER before setting the clock (while the dash

lines are stiil displayed).

Note: Throughout this manual, you will note references to a

tone that signals the end of a cooking or timing operation. If

you have cancelled the end-of-cycle signal, disregard these

references.

C. Oven Light

The oven light will come on when the door is opened. It will

also come on when the oven is operating.

D. Set the Clock.

1. Press RESET.

2. Enter the time of day by pressing the numbers in

sequence. For example, if it is 10:35 (a.m. or p.m.), press

number pads 1,0, 3 and 5, in that order.

3. Press CLOCK twice. The clock is now set. If oven

power is interrupted (for example, if the supply circuit is dis

connected, or if there is a power failure), all programming

THE CONTROL PANEL =

Model RW321T and

RWG321T

READOUT DISPLAY — Normally shows

time of day.

• Shows remaining time when cooking by

time or using the TIMER.

NUMBERS — Always press numbers first

when programming the oven. Press in the

same order as you would write them.

COOKMATIC LEVEL — Programs

cooking power level. Press after pressing

number pad corresponding to cook levels

imprinted on control panel. (See page 7.)

RESET — Always press before •

programming oven. Can also be pressed

during programming to cancel mistakes.

When using TIMER while cooking, press

to see cooking time.

START — Starts oven operation. •

instructions will be erased, and dashes will appear in the

display. You must then reset the desired signal options and

clock as indicated above.

. Check operation of the interlock systems. The

START and STOP pads turn the oven on and off.

Microwave energy is generated only when the door is closed,

cooking time or temperature has been set, and START

has been pressed. In addition, the oven has interlock

switches to assure no microwave energy is generated when

the door is open. To check or remove food before the cooking

time has elapsed, you may either press STOP or open the

oven door to turn the oven off. Before the oven door opens,

hidden interlock switches sense the motion of the door han

dle and automatically turn the oven off.

Here is how you may check the operation of

START, STOP and the interlock switches:

1. Place a glass of water in oven and close oven door.

2. Press RESET.

3. Press 5, then 0.

4. Press START . The oven should operate and the oven

light should come on.

5. Press STOP The oven should shut off immediately

and the sound of the motor should cease. The oven light

should go out.

6. Open oven door fully. The oven light should come on

when the door is opened.

7. Press RESET.

If under any of the preceding conditions the oven does not

operate as stated, do not use it. Call your Amana dealer or

authorized service agency.

TIMER — Lets you time a separate task,

even when the oven is cooking. Press

after pressing after pressing numbers for

time to be measured. (See page 7.)

CLOCK — Sets time of day. Press twice

after pressing numbers for the current

time. (See page 6.)

STOP — Stops oven. The oven can also

be stopped by opening the door.

IF YOU MAKE A MISTAKE

• If the oven is operating, press

STOP, then press RESET. This

cancels everything. You must

program the oven again.

• If the oven is not operating yet,

press RESET. This cancels

everything. You must program the

oven again.

1 2 3 4 5 6 7 8 9

Comments to this Manuals

No comments

Amana RADARANGE RW321T User Manual Page 6

Comments to this Manuals