Amana RSS User Manual Page 95

  • Download
  • Add to my manuals
  • Print
  • Page
    / 124
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 94
FIRE OR EXPLOSION - TO AVOID THE RISK OF ELECTRICAL SHOCK, PERSONAL
INJURY, OR DEATH, DISCONNECT POWER TO THE OVEN BEFORE SERVICING.
DISASSEMBLY PROCEDURES - RST MODELS
RC231002 Rev. 3 94
TOP BURNER SPARK IGNITORS (RSS MODELS)
1. Disconnect electricity at main disconnect plug.
2. Remove top burner grates and main top.
3. Remove top burner assembly (right and left).
4. Remove control panel.
5. Remove eight (8) right screws securing burner box in
place.
6. Gently maneuver control panel to free burner box.
7. Disconnect high voltage ignitor leads from spark
module.
8. Remove two (2) screws securing the top burner
mounting support to the burner box.
9. Straighten tabs on the ignitor grounding bracket and
remove bracket from the top burner mounting sup-
port.
10. Remove speed clip securing the spark ignitor to the
top burner mounting bracket (Clip must be re-used,
do not break.)
11. Reverse procedure to reinstall new top burner ignitor.
NOTE: Be certain the ignitor grounding bracket is
tight on the top burner support. Also be sure the gap
between the ignitor grounding bracket dimple and top
of ignitor is 1/8" (-1/32" + 0").
BURNER BOX
Sealed Burner Models
1. Shut off power to the range. Shut off main gas supply.
2. Remove grates, burner caps, and main top.
3. Remove six (6) screws securing burner box to side
panels.
4. Remove control panel. Remove two (2) screws
securing manifold to filler trim.
5. Disconnect two (2) feed tubes to manifold.
6. Lift up burner box and disconnect electrode leads at
spark module.
7. To replace the burner box, remove venturi assem-
blies and electrode leads, burner box baffles with
seal, manifold and tubing to venturi. Reassemble
components on replacement burner box. Be sure
baffle seal is correctly positioned.
Check all gas connections for gas leaks with leak
detector after reassembly.
TOP BURNER VENTURI
Sealed Burners
1. Shut off power to the range. Shut off main gas supply
to the range.
2. Remove grates, burner caps, and main top.
3. Disconnect feed tube from burner valve to venturi.
4. Remove two (2) screws securing venturi to burner
box.
5. Remove screw securing mounting bracket to venturi
and remove electrode from bracket.
Be sure to check venturi feed tube connection for gas
leaks with leak detector after reassembly.
ELECTRODE WIRE WITH SOCKET
Sealed Burner Units (Aluminum Tubing Gas Feed)
1. Shut off power to the range. Shut off main gas supply
to the range.
2. Remove grates, burner caps, and main top.
3. Disconnect tube to venturi. Remove two (2) screws
securing venturi assembly to burner box.
4. Remove screw securing mounting bracket to venturi
assembly and remove electrode socket.
5. Remove burner box.
6. Disconnect electrode at spark module.
Check gas connections for leaks with leak detector
after reassembly.
BURNER BOX BAFFLE
Sealed Burner Models (Only On Aluminum Tubing
Gas Feed)
1. Shut off power to the range.
2. Remove grates, burner caps, and main top.
3. Remove three (3) screws securing baffle to burner
box. Baffle and silicone seal can now be removed.
Silicone seal must be located on baffle to assure
proper top burner operation.
SPARK MODULE (FREE STANDING MODELS)
1. Disconnect electricity at main disconnect plug. Shut
off main gas supply to the range.
2. Remove main top.
3. Remove burner box.
4. Remove two (2) screws securing spark module bracket
to insulation retainer.
On models without sealed burners, the spark module
is located on the left side of the range.
The sealed burner models incorporate a spark mod-
ule on both the left and right sides of the range or one
(1) spark module with four (4) outputs on left side.
5. Remove screw securing module to mounting bracket.
Bend retaining tab to remove module from bracket.
6. Disconnect wire leads to module.
Check wiring diagram for proper wire identification
when reinstalling.
Check gas connections for leaks with leak detector or
soap solution.
Page view 94
1 2 ... 90 91 92 93 94 95 96 97 98 99 100 ... 123 124

Comments to this Manuals

No comments

Panasonic ES881 manuali

Manuali dei proprietari e guide per l'utente per Rasoi elettrici Panasonic ES881.
We fornisce 1 manuali pdf Panasonic ES881 per scaricare gratuitamente in base al tipo di documento: Manuale Utente






Più prodotti e manuali per Rasoi elettrici Panasonic

Modelli Tipo di Documento
ES 8807 Manuale Utente   Инструкция по эксплуатации Panasonic ES 8807, 11 pagine
ES 8109 Manuale Utente   Инструкция по эксплуатации Panasonic ES 8109, 11 pagine
ER412 Manuale Utente   Инструкция по эксплуатации Panasonic ER412, 3 pagine
ER121 Manuale Utente     Panasonic ER121 User Manual, 16 pagine
ES119 Manuale Utente    Panasonic ES119 User Manual, 8 pagine
ES 2013 Manuale Utente   Инструкция по эксплуатации Panasonic ES 2013, 4 pagine
ES113 Manuale Utente    Panasonic ES113 User Manual, 20 pagine
ES8080 Manuale Utente    Panasonic ES8080 User Manual, 17 pagine
ES882 Manuale Utente     Panasonic ES882 User Manual, 20 pagine
ES2205 Manuale Utente    Panasonic ES2205 User Manual, 16 pagine
EW1000 Manuale Utente    Panasonic EW1000 User Manual, 28 pagine
ES7015 Manuale Utente     Panasonic ES7015 User Manual, 20 pagine
Epilator ES2045 Manuale Utente   Panasonic Epilator ES2045 Manual del usuario, 18 pagine
ES765 Manuale Utente     Panasonic ES765 User Manual, 20 pagine
RECHARGEABLE SHAVER ES4011 Manuale Utente    Panasonic RECHARGEABLE SHAVER ES4011 User Manual, 16 pagine
ES207 Manuale Utente     Panasonic ES207 User Manual, 12 pagine
ES8023 Manuale Utente     Panasonic ES8023 User Manual, 24 pagine
Wet/Dry Rechargeable Shaver ES8056 Manuale Utente    Panasonic Wet/Dry Rechargeable Shaver ES8056 User Manual, 17 pagine
ES726 Manuale Utente     Panasonic ES726 User Manual, 22 pagine