Amana AGR4230BAB Installation Manual download pdf (Page 10)

IMPORTANT: If the back of the range is more than 2" (5.1 cm)

from the mounting wall, the rear range foot may not engage the

bracket. Slide the range forward and determine if there is an

obstruction between the range and the mounting wall. Changes

to the gas supply must be performed by a qualified service

technician. If you need assistance or service, refer to the

“Assistance or Service” section of the Use and Care Guide for

contact information.

6. Repeat steps 1 and 2 to ensure that the range foot is

engaged in the anti-tip bracket.

If the rear of the range lifts more than ½" (1.3 cm) off the floor

without resistance, the anti-tip bracket may not be installed

correctly. Do not operate the range without anti-tip bracket

installed and engaged. Please reference the “Assistance or

Service” section of the Use and Care Guide, or the cover or

“Warranty” section of the User Instructions, to contact

service.

Level Range

1. Place a standard flat rack in oven.

2. Place level on the rack and check levelness of the range, first

side to side; then front to back.

3. If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

4. Use a ³⁄₈" drive ratchet and slip-joint pliers to adjust leveling

legs up or down until the range is level.

5. Push range back into position.

6. Check that rear leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking

performance.

Electronic Ignition System

Initial lighting and gas flame adjustments

Cooktop and oven burners use electronic igniters in place of

standing pilots. When the cooktop control knob is turned to the

“IGNITE” position, the system creates a spark to light the burner.

This sparking continues until the control knob is turned to the

desired setting.

When the oven control is turned to the desired setting, a hot

surface igniter heats to a bright orange and ignites the gas. No

sparking occurs. The glow bar remains on while the burner

operates.

Check Operation of Cooktop Burners

1. If control panel and knobs were removed earlier, reinstall

knobs.

2. Push in and turn each surface unit control knob to “IGNITE”

position. The flame should light within 4 seconds.

3. Turn control knob to “HI” position after burner lights.

4. Check each cooktop burner for proper flame. The small inner

cone should have a very distinct blue flame ¼" (0.64 cm) to

½" (1.3 cm) long. The outer cone is not as distinct as the

inner cone.

5. Turn the control knob quickly to the “LO” position after the

burner lights. If the flame goes out, turn the control knob to

the “OFF” position.

6. Check each cooktop burner for proper low flame. The low

flame should be a minimum, steady blue flame. The flame

size should be ¼" to ³⁄₈" (0.64 cm to 0.95 cm) high.

If the low flame needs adjusting:

1. Turn control knob to the “LO” setting and remove control

knob.

2. Insert a small flat-blade screwdriver into the valve stem. Turn

the valve adjusting screw to obtain the smallest flame that will

not go out when the control of a cold burner is quickly turned

from “HI” to “LO.” Turn right to decrease flame height. Turn

left to increase flame height. Repeat for other cooktop

burners as needed.

3. Replace control knob.

A. Outer cone

B. Inner cone

A. Valve stem

OFF

IGNITE

MED

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

Comments to this Manuals

No comments

Amana AGR4230BAB Installation Manual Page 10

Comments to this Manuals

Related products and manuals for Ovens Amana AGR4230BAB