Amana AMAP061BW Owner's Manual Page 15
- Page / 68
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
15
NOTE: If the wall thickness is 8½" (21.59 cm) or more, add
aluminum flashing over the bottom of the frame opening to
assure water is unable to enter the area between the inner
and outer wall.
Prepare and Install the Cabinet
Place the cabinet into the opening with the bottom channel
resting rmly on the bottom rail of the wood frame. Position
the cabinet so it is properly tilted for water removal.
2. Place and position cabinet
Assemble brackets. See “Install Support Brackets” in the
“Window Installation” section. Nail a wooden strip to the
outside wall to be used in conjunction with the angled sill
support brackets.
4. Place and position cabinet
Screw or nail the cabinet to the wooden frame using shims if
the frame is oversized to eliminate possible noise. Remember
to maintain proper slope for water elimination.
Reinstall the chassis into the cabinet. See the “Install the Chassis
into the Cabinet” section.
5. Secure cabinet and install chassis
Masonry Construction
1. Cut or build a wall opening in the masonry wall similar to the
frame contruction. See the “Wall Installation Instructions –
240 V Models” section for a wall thickness greater than 8½"
(21.59 cm).
2. Secure the cabinet in place using masonry nails or masonry
anchor screws. Or build a frame using the instructions found
in the “Wall Installation Instructions – 240 V Models” section.
3. Make sure the masonry above the cabinet is supported well.
Use the existing holes in the cabinet or additional drilled holes
to fasten the cabinet at various positions. Make sure that the
side louvers are clear of any obstructions.
4. Install the exterior cabinet support brackets according to
“Prepare and Install the Cabinet” in the “Wall Installation
Instructions – 240 V Models” section. Caulk or ash with
aluminum if needed. This will provide a tight seal around
the top and sides of the cabinet.
5. For a more aesthetically pleasing installation, apply wood trim
molding around the sides of the cabinet without obstructing
the side louvers.
Secure the bottom channel to the wood frame with two large
1" (2.5 cm) wood screws.
3. Secure bottom channel to frame
Slide the chassis from the cabinet. See the “Prepare Air
Conditioner for Installation” section for more details.
1. Remove chassis
Aluminum
ashing
Caulk as
needed
Gap size 5/16"
to 3/8"
Support
bracket
Wooden
strip
- Room Air Conditioner 1
- Climatiseur 1
- Acondicionador de aire para 1
- AIR CONDITIONER SAFETY 2
- INSTALLATION REQUIREMENTS 3
- Power Supply Cord—All Models 4
- Tools Required—All Models 4
- Parts Supplied: 4
- 6,000-12,000 BTU models 4
- Parts Supplied— 5
- 15,000-24,000 BTU Models 5
- Window Opening Measurements 5
- Location Requirements— 5
- Window Installation 5
- 2. Place block on windowsill 6
- 2. Attach upper foam seal 6
- 3. Attach screws 7
- 2. Install top channel 7
- 1. Install side curtain 8
- 3. Extend side curtains 9
- 7. Install foam seal 9
- 6. Secure lower sash 9
- 3. Remove faceplate screws 10
- 4. Remove faceplate 10
- Attach foam gasket 11
- Slide in side panels 11
- Remove right-side screws 11
- Remove chassis 11
- Attach side panels 11
- Install Support Brackets 12
- Extend Side Panels 13
- 2. Build frame 14
- 1. Remove chassis 15
- Selecting the Mode 16
- Features 16
- Selecting the Fan Speed 16
- Adjusting the Temperature 16
- MODESPEED 17
- Using the Remote Control 18
- Replacing the battery 18
- 2. Removing the air lter 19
- 1. Removing the air lter 19
- TROUBLESHOOTING 20
- ASSISTANCE OR SERVICE 21
- XLS PRODUCTS WARRANTY FOR 22
- AIR CONDITIONERS 22
- AVERTISSEMENT : 23
- CONSERVEZ CES INSTRUCTIONS 23
- EXIGENCES D’INSTALLATION 24
- Cordon d’alimentation — 25
- Pièces fournies : 25
- Modèles à 6 000-12 000 BTU 25
- Pièces fournies: 26
- Modèles à 15 000-24 000 BTU 26
- Exigences d’emplacement – 26
- Installation dans la fenêtre 26
- Mesurer la taille de la cale 27
- d’espacement nécessaire 27
- Mesurer et marquer le centre 27
- 1. Déballer le climatiseur 28
- 3. Fixer les vis 28
- AVERTISSEMENT 29
- 4. Retirer la plaque avant 31
- 1. Déballer le climatiseurr 31
- Installer supports de montage 33
- 2. Construire le cadre 35
- 1. Retirer le châssis 36
- Sélectionner le mode 37
- Caractéristiques 37
- Réglage de la température 37
- Remplacer las piles 39
- 2. Retirer le ltre à air 40
- 1. Retirer le ltre à air 40
- DÉPANNAGE 41
- ASSISTANCE OU SERVICE 42
- GARANTIE DE XLS PRODUCTS 43
- POUR LES CLIMATISEURS AMANA 43
- ADVERTENCIA 44
- REQUISITOS DE INSTALACIÓN 45
- 2" 47
- /2" 48
- 3. Fijar los tornillos 49
- 2. Instale el canal superior 49
- 4. Retire la placa frontal 52
- 3. Fijación del gabinete 54
- 2. Cierre la ventana 54
- 3. Fije soportes montados 55
- 2. Ensamble los soportes 55
- 1. Inserte banda del marco 56
- 2. Construya marco 57
- 1. Retire el chasis 58
- Cómo usar el control remoto 61
- Cómo reemplazar las baterías 62
- SOLUCIÓN DE PROBLEMAS 64
- AYUDA O SERVICIO TÉCNICO 65
- GARANTÍA DE XLS PRODUCTS 66
Related products and manuals for Unknown Amana AMAP061BW
Unknown Amana PBC093G00CB Brochure
(2 pages)
(2 pages)
Unknown Amana AZF33X16DW Energy Guide
(2 pages)
(2 pages)
Unknown Amana ART318FFDW Warranty
(4 pages)
(4 pages)
Unknown Amana ART318FFDW Energy Guide
(1 pages)
(1 pages)
Unknown Amana NTW4516FW Warranty
(3 pages)
(3 pages)
Unknown Amana AMAP101AW Owner's Manual
(44 pages)
(44 pages)
Unknown Amana AMAD501AW Warranty
(1 pages)
(1 pages)
Unknown Amana PTH074G35AXXX User Manual
(1 pages)
(1 pages)
Unknown Amana AMC4322GB Dimensions Guide
(1 pages)
(1 pages)
Unknown Amana ACR4503SFS Specifications
(1 pages)
(1 pages)
Unknown Amana AZC31T15DW Energy Guide
(2 pages)
(2 pages)
Unknown Amana AGG222VDW Warranty
(3 pages)
(3 pages)
Unknown Amana PBE093G35CC Brochure
(2 pages)
(2 pages)
© 2020, manymanuals.com. All rights reserved. | 0.126 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals